How many different techniques for bringing a signal into the shack have you experimented with? I’ve tried a number of them. My first shack, outfitted with a Heathkit HW-101 transceiver, was in the basement. Immediately to the left of the HW-101 was the foundation, sill plate, and as yet unfinished studded wall. There was also a single window. When I was using an end-fed long wire as my radiator I merely tied it
off outside the window and then continued inside with a short insulated extension that slipped under the frame of the closed window and terminated it at a post on an MFJ antenna tuner. Everything changed when I switched to a G5RV fed by coax. That time I drilled a hole directly through the outer shingles and plywood wall and on through my new inner wall (diagonal furring strips). I lined the hole with a short piece of PVC tubing that was filled on both ends with Coax-Seal putty.
Things changed when I moved up one floor to the now vacant bedroom left to me by my son when he moved away to college. I placed a copper-clad panel between the window and sill and studded it with through-mount SO-239 connectors. These afforded me
access to a roof-mounted VHF antenna, a tree-bound G5RV, and a ground mounted
Gap Titan vertical. At this higher elevation the ground wire was getting a little longer than I wanted it (10 meter in-shack radiation was sometimes a problem).
Then we moved to the new house which is a colonial; two full floors and a basement. First I adapted the window panel to fit my new second floor window. Later I decided to change things because I wanted to install the shortest possible RF ground wire and put
the screen back in the window (I now have one-piece screens, they do not move
on a track). An advertisement for the MFJ soffit entrance panel got me thinking about a new entrance for the transmission line. If I purchased the MFJ unit I would have to figure out how to remove a section of the soffit that makes up part of the overhang of my second floor room. I found that this involved the removal of lots of nails, molding, and panels. I like to keep a job simple. My solution was to drill a hole directly through the soffit right on up to the floor of my shack. My soffit is covered with vinyl siding. Under the siding is what looks like 3/4” plywood followed by about 9” of insulation-filled space which is topped by the floor boards and rug of my ham shack. My room also has walls and a bookcase; I did not want my drill bit to come up in either one of those places.
So how did I do it? I first made very careful measurements as to where I wanted the entrance hole to emerge from my rug. This was in the corner of the room and about
5” from each adjoining wall. If I missed my mark I could end up in the wall or under the bookcase. I dropped a weighted line (plumb line) out the window and measured from the place on the rug where I wanted the hole to the edge of the line going out the window. Then I went outside and marked the point on the soffit that was exactly
the same distance from the string line as the prospective entrance point was. All I needed now was a depth measurement. I measured from a point 5” inside the window to the outside vinyl siding. Then I was able to find the intersection of the two lines; I had my drilling spot. I purchased a long 5/8” x 16” spade bit (it will make a clean hole that is 14” deep). I could have got one that was 1-1/4” in diameter, but that would have more than doubled the $10.00 price. I drilled the hole from the outside and in spite of my careful measurements I was about 2” off, but not in the wall or under the bookcase. I then opened up each hole (floor, siding, soffit) with a 1-1/4” spade bit that only had to penetrate less than one inch on both sides. Then I attempted to feed the coax through the hole. That did not go well. Although the hole was large enough the coax tended to go off to one side or another and never quite make it to the shack floor. I solved this problem by
cutting a piece of ¾” Schedule 40 PVC and lining the hole with that. The end that protruded into the shack was terminated with a ¾” connector that is usually used to connect two lengths of PVC tubing. The connector prevented the PVC from falling out of the hole. On the soffit side I used some liquid nails to glue a chrome sink drain surround over the hole to make it look better and that was it.
Now all I have to do is run in a ground wire and attach a ground bus bar to the wall where the coax enters. I may also close off each end of the PVC with some sort of plug such as a piece of rubber or flexible plastic with radiating cuts in the middle to allow the coax to pass through. I will tightly close off each entrance point with Duct Seal (a kind of putty used by electricians) so all weather and insects will remain outside.
List of Materials and Special Tools:
(1) 5/8” x 14” spade bit (wood boring bit) $10.00
(1) 1-1/4” x 4” spade bit from a set $1.50
(1) 1 pound package of GB Duct Seal $ 1.75
(1) ¾” Sched. 40 PVC junction $ 0.40
(1) 10’ x ¾” SCH 40 PVC pipe; ID 3/4″, OD ~ 1-1/16″ $ 3.00
(1) Wash basin drain surround junk box item
Nice install Ken; I’m getting ready to re-do my shack very soon. We are just about finished with a total remodeling of the house. One of the things we did was have all the windows replaced; I really didn’t want to use a homebrew window panel for feedline access (that’s what I used with the old window) and had been mulling my options when I suddenly realized my access is almost ready now. In the remodeling we turned an upstairs hall closet into a laundry area with a stacking washer/dryer. The former laundry room, which is right next to my shack still has the old dryer vent (blocked with insulation) sticking out the exterior wall. Simple matter to cut an opening in the wall between the two rooms (I’m going to borrow your idea with the PVC pipe), route my feedlines through the dryer vent and then through the PVC in the wall. In order to have a short run for my RF ground I’m going to drill a 1/4″ hole through the brick and then into the shack and run my ground wire out through that (with some sealant around the exit hole). Back when I was in high school, 35 years ago, I ran my feedline through the crawlspace of our house and up through a hole I drilled in the closet floor….can’t remember now if I got my parent’s permission to drill that hole or not!
Phil: It sounds like you too are getting ready for winter (does it ever get cold down your way?). I like the idea of using the old dryer vent. That will cut down on the work involved. After our last 5-day power loss during Irene I am considering using my dryer vent to take in a feed from a generator (don’t have a generator yet).
RE the stacking washer & dryer, I really like those. That must have been some work getting the plumbing to the closet.
Ken we usually have some pretty cold wx in Jan/Feb…not uncommon for it to get down to the single digits but the nice thing is that it doesn’t last long. Had a plumber and an electrician do the work for the laundry unit. The XYL is really happy that the w/d is now on the same level as our bedroom, me too since I probably do the laundry as much as she does. I’m pretty pumped about re-doing the shack. It’s been painted, new hardwood floors. I have some now not needed sliding closet doors that I’m going to brace and make an L shaped workbench and operating desk out of; will span the back wall and a portion of the side wall. Will post some pics on Flickr when I get it all finished. Also have a Gap Challenger to install and I think I’m going to order a Carolina Windom too.
Phil: That sounds like a great ham shack project. I think you are really going to love the Gap Challenger too. Please do post photographs of the entire process, including the new workbench.
Ken, you did another one of your fablous installs with great descriptions, and photos. Now I am taking photo’s of my feed entrance into the shack. Pictures to follow. : )
Thanks, Dan! There are a lot of ways to get that coax in and I’d like to see how you did it.